Study HIGH Quality LEED-AP-BD-C Free Study Guides and Exams Tutorials [Q134-Q149]

Study HIGH Quality LEED-AP-BD-C Free Study Guides and Exams Tutorials [Q134-Q149]

April 6, 2024 latestexam 0 Comments

Rate this post

Study HIGH Quality LEED-AP-BD-C Free Study Guides and Exams Tutorials

Download USGBC LEED-AP-BD-C Exam Dumps to Pass Exam Easily

Q134. Green Infrastructure (GI) and Low-Impact Development (LID) rainwater management strategies improve upon the conventional approach for rainwater management by

replicating a site’s natural hydrology

discharging rainwater at a faster rate

increasing a site’s impervious surface

providing a greater volume of rainwater detention

Explanation
Green Infrastructure (GI) and Low-Impact Development (LID) rainwater management strategies improve upon the conventional approach for rainwater management by replicating a site’s natural hydrology. GI and LID are design approaches that use various practices to mimic the natural water cycle and reduce the negative impacts of development on the environment. They aim to preserve, restore, or create natural features that can capture, infiltrate, evaporate, or reuse rainwater on site, rather than conveying it to a centralized stormwater system. By doing so, they can reduce runoff volume and peak flow, improve water quality, enhance groundwater recharge, increase biodiversity, and create more attractive and resilient landscapes. Therefore, option A is the correct answer. The other options are not true for GI and LID strategies. Discharging rainwater at a faster rate (option B) would increase the risk of flooding, erosion, and pollution downstream. Increasing a site’s impervious surface (option C) would reduce the infiltration and evaporation of rainwater and increase runoff and heat island effects. Providing a greater volume of rainwater detention (option D) would not necessarily improve the site’s hydrology, as detention is only a temporary storage of rainwater that does not address the runoff quality or quantity issues.For more information on GI and LID rainwater management strategies, you can refer to the LEED v4 Reference Guide for Building Design and Construction1or the Green CE course on Rainwater Management for LEED v4.1 Projects2.

Q135. A new commercial building is being designed to use small capacity air handling units. To meet the requirements of the Carbon Dioxide Monitoring strategy in the Indoor Environmental Quality Credit, Enhanced Indoor Environmental Quality Strategies, where would CO2 monitors need to be located?

In each occupied space

In each densely occupied space

In each occupied space and outdoors

In each occupied space over 500 ft2 (46 m2)

Explanation
According to the LEED v4 Reference Guide for Building Design and Construction, the Carbon Dioxide Monitoring strategy requires CO2 monitors to be located in each densely occupied space, which is defined as a space with a design occupant density of 25 people or more per 1,000 square feet (93 square meters). This strategy is intended to provide feedback on ventilation system performance and indoor air quality12 References: 1: LEED v4 Reference Guide for Building Design and Construction, Indoor Environmental Quality Credit: Enhanced Indoor Air Quality Strategies, Option 2: Additional Enhanced IAQ Strategies, Strategy 3: Carbon Dioxide Monitoring, page 704. 2: LEED v4 Reference Guide for Building Design and Construction, Glossary, page 1019.

Q136. The owner of a large multi-building property is seeking LEED certification. In determining the LEED project boundaries the LEED AP may include non-contiguous parcels of land if

the parcels are used for temporary uses such as parking or staging that is owned and managed by a third party

the parcels directly support or are associated with normal building operations and are accessible to the project’s occupants

the parcels are part of an existing public preservation easement or resource protection area that is directly adjacent to the LEED project boundary

the parcels are part of a land trust or conservation organization for which the LEED project provides financial support for in the Sustainable Sites Credit, Site Development Credit, Protect or Restore Habitat, Option 2. Financial Support

Explanation
In determining the LEED project boundaries, the LEED AP may include non-contiguous parcels of land if the parcels directly support or are associated with normal building operations and are accessible to the project’s occupants. This is according to the Minimum Program Requirements (MPRs) for LEED v4.1, which state that non-contiguous parcels of land may be included within the LEED project boundary if they meet these criteria1. Facilities such as parking lots, bicycle storage, shower/changing facilities, and/or on-site renewable energy that are outside of the LEED project boundary may also be included in certain prerequisites and credits if they directly serve the LEED project and are not double-counted for other LEED projects1. The other options are not valid reasons to include non-contiguous parcels of land within the LEED project boundary.
Temporary uses such as parking or staging that are owned and managed by a third party do not directly support or are associated with normal building operations of the LEED project1. Existing public preservation easements or resource protection areas that are directly adjacent to the LEED project boundary are not considered as part of the LEED project boundary, unless they are owned by the project owner or the project team has permission to use them2. Land trusts or conservation organizations for which the LEED project provides financial support are not considered as part of the LEED project boundary, unless they are located within the same EPA Level III ecoregion as the project site3.
References:
*Minimum Program Requirements (MPRs) – U.S. Green Building Council
*NC-v4.1 MPR2: Must use reasonable LEED boundaries | LEEDuser
*Site development – protect or restore habitat, p. 2

Q137. What is the best strategy for a LEED AP to suggest in order to quantify the impact of increasing the window-to-wall ratio on a Building Design and Construction project?

Compare the current project to other similar projects

Monitor the HVAC loads throughout the life of the project

Perform a simple box energy model before the completion of the schematic phase

Review Green Business Certification Inc. (GBCI)’s comments on the energy model submission

Explanation
This option allows the project team to evaluate the impact of different window-to-wall ratios on the energy performance of the building, and to optimize the design accordingly. A simple box energy model is a preliminary analysis tool that can be used to compare different design alternatives and inform decision making in the early stages of the project12.
References: = [LEED v4: Building Design + Construction Guide], LEED v4 for Building Design and Construction: Energy and Atmosphere, The impacts of window to wall ratio and window orientation on building energy consumption and CO2 emissions under climate change. Message has links.

Q138. A mixed-use development is located 1/2 mi. (0.80 km) from a future commuter rail line station.Which of the following pieces of information is needed when determining whether the rail line station can contribute to Location and Transportation Credit, Access to Quality Transit?

Discounted rail pass availability

Rail line station construction completion date

Connections to transfer routes

Passenger capacity

Explanation
The rail line station construction completion date is needed when determining whether the rail line station can contribute to Location and Transportation Credit, Access to Quality Transit. This is because the credit requires that the transit service must be existing or planned to be in operation within two years of the project’s occupancy1. Discounted rail pass availability, connections to transfer routes, and passenger capacity are not relevant for this credit1.
References:
*Access to quality transit, p. 1

Q139. What stage of LEED for Neighborhood Development certification listed below is eligible for points under Building Design and Construction: New Construction, Location and Transportation Credit, LEED for Neighborhood Development Location?

LEED v4, LEED for Neighborhood Development Conditional Approval

LEED for Neighborhood Development Pilot, Stage 3 LEED for Neighborhood Development Certified Project

LEED for Neighborhood Development Pilot, Stage 1 LEED for Neighborhood Development Pre-reviewed Plan

LEED 2009, Stage 1 Conditional Approval of LEED for Neighborhood Development Plan

Explanation
The only stage of LEED for Neighborhood Development certification that is eligible for points under Building Design and Construction: New Construction, Location and Transportation Credit, LEED for Neighborhood Development Location, is LEED for Neighborhood Development Pilot, Stage 3 LEED for Neighborhood Development Certified Project.This is because the credit requires that the project be located within the boundary of a development that has achieved certification under LEED for Neighborhood Development (either Stage 2 or Stage 3 under the Pilot or 2009 rating systems, or Certified Plan or Certified Project under the LEED v4 rating system)1The other stages listed in the question are either conditional approvals or pre-reviews that do not guarantee certification23References:1: LEED v4 Reference Guide for Building Design and Construction, Location and Transportation Credit: LEED for Neighborhood Development Location, page
460.2: LEED for Neighborhood Development Location – Above Green33: LEED v4: Building Design + Construction Guide – U.S.Green Building Council1

Q140. A design team is pursuing Indoor Environmental Quality Credit, Indoor Air Quality Assessment. The building is 1,000 ft2 (93 m2) and has a 10 ft. (3 m) ceiling height. In order to earn the credit, what is the required volume of supply air for the entire building flush-out?

3,500,000 ft3 (99 108 m3)

10,000,000 ft3 (283 168 m3)

14,000,000 ft3 (396 435 m3)

35,000,000 ft3 (991 089 m3)

Explanation
According to the LEED Reference Guide for Building Design and Construction1, the Indoor Environmental Quality Credit, Indoor Air Quality Assessment, Option 1. Flush-Out requires the project to perform a building flush-out by supplying a total air volume of 14,000 cubic feet of outdoor air per square foot of gross floor area while maintaining an internal temperature of at least 60°F and no higher than 80°F and relative humidity no higher than 60%. The gross floor area of the building is 1,000 ft2 and the ceiling height is 10 ft, so the required volume of supply air for the entire building flush-out is:
14,000 ft3/sf x 1,000 sf = 14,000,000 ft3
References:
* LEED Reference Guide for Building Design and Construction v4

Q141. A new athletic facility contains a laundry room which is adjacent to the locker rooms. Whichstrategy will contribute toward the Interior Cross-Contamination Prevention strategy in Indoor Environmental Quality Credit, Enhanced Indoor Air Quality Strategies?

Relocate the laundry facility to the basement

Naturally ventilate the laundry space per ASHRAE 62.1-2010

Install particle filters, with a MERV of 13 or higher or F7

Provide a ventilation system specifically for the laundry facility that has no recirculating air

Explanation
The strategy that will contribute toward the Interior Cross-Contamination Prevention strategy in Indoor Environmental Quality Credit, Enhanced Indoor Air Quality Strategies is to provide a ventilation system specifically for the laundry facility that has no recirculating air. This is because the laundry facility is a space where hazardous gases or chemicals may be present or used, such as detergents, bleach, or fabric softeners.
According to the LEED v4 Reference Guide for Building Design and Construction, the project must
“sufficiently exhaust each space where hazardous gases or chemicals may be present or used (e.g., garages, housekeeping and laundry areas, copying and printing rooms), using the exhaust rates determined in EQ Prerequisite Minimum Indoor Air Quality Performance or a minimum of 0.50 cfm per square foot (2.54 l/s per square meter), to create negative pressure with respect to adjacent spaces when the doors to the room are closed.For each of these spaces, provide self-closing doors and deck-to-deck partitions or a hard-lid ceiling.”1Therefore, option D is the correct answer. The other options will not prevent cross-contamination from the laundry facility to the locker rooms. Relocating the laundry facility to the basement (option A) may reduce the exposure of the occupants to the laundry chemicals, but it will not eliminate the possibility of cross-contamination to other spaces in the basement. Naturally ventilating the laundry space per ASHRAE
62.1-2010 (option B) may not provide sufficient exhaust to create negative pressure and prevent cross-contamination, especially if the outdoor air quality is poor or the natural ventilation is not well designed.
Installing particle filters, with a MERV of 13 or higher or F7 (option C) may improve the air quality in the laundry space, but it will not prevent the hazardous gases or chemicals from escaping to the adjacent spaces through the ventilation system or the gaps in the doors or ceiling.References: LEED v4 Reference Guide for Building Design and Construction, p.6881; ASHRAE Standard 62.1-2010, Section 6.2.52

Q142. Qualifying spaces for the Sustainable Sites Credit. Places of Respite must tgj

be located outdoors near a water feature

be located at least 20 ft. (6 m) from a smoking area

have provisions for direct medical care to be delivered in the area

have options for shade or indirect sun for a portion of seating spaces

Explanation
According to the LEED AP BD+C V4 reference guide for Healthcare, places of respite must be outdoors or located in interior spaces with views of nature, and have options for shade or indirect sun for a portion of seating spaces. The other options are either incorrect or not required by the credit. References: LEED AP BD+C V4 reference guide for Healthcare, Places of respite

Q143. How is the distance between the project site and the manufacturing location determined for Materials and Resources Credit. Building Disclosure and Optimization – Sourcing of Raw Materials. Option 2. Leadership Extraction Practices?

Roadway distance

Straight line distance

Rail freight distance

Air freight distance

Explanation
The distance between the project site and the manufacturing location is determined by the straight line distance. This is because the LEED v4 Reference Guide for Building Design and Construction states that the distance should be measured as the crow flies1. The straight line distance is the shortest distance between two points on a plane, regardless of the mode of transportation or the road conditions. The image that you sent shows the straight line distance between the project site and the manufacturing location as the line segment AB.
References:
* LEED v4 Reference Guide for Building Design and Construction, Materials and Resources Credit:
Building Product Disclosure and Optimization – Sourcing of Raw Materials, page 551

Q144. What is the system boundary that a building life cycle analysis must be defined to account for?

Cradle-to-gate

Cradle-to-grave

Cradle-to-cradle

Cradle-to-building

Explanation
The system boundary that a building life cycle analysis must be defined to account for is the cradle-to-grave stage, which includes the production, construction, use, and end-of-life stages of the building. This stage covers all the inputs and outputs of the building system, such as materials, energy, water, emissions, waste, and maintenance.
References:
*Life Cycle Assessment of Buildings: Technical Guidance
*Life-cycle assessment – Wikipedia
*Conducting a Life Cycle Assessment – GSA Sustainable … – SFTool

Q145. A project team is using the whole building simulation model to quantify the percentage of energy savings for the project. Which of the following should remain the same for both the baseline building and the proposed building?

Building operating schedule and occupancy hours

Building operating schedule and total window area

Building envelope construction and occupancy hours

Total window area and building envelope construction

Explanation
This option requires the project team to use the same building operating schedule and occupancy hours for both the baseline building and the proposed building in the whole building simulation model1. This option ensures that the energy savings are calculated based on the same level of building activity and occupancy, which are major factors that affect the energy performance of a building2.
References: = LEED v4: Building Design + Construction Guide, [Whole Building Energy Simulation – an overview | ScienceDirect Topics].

Q146. Which of the following project team members should be integrated early into the design phase to assist with earning the Materials and Resources Prerequisite, Construction and Demolition Waste Management Planning?

Owner

Contractor

Occupants

Facility manager

Explanation
Contractor
The contractor is the project team member who should be integrated early into the design phase to assist with earning the Materials and Resources Prerequisite, Construction and Demolition Waste Management Planning.
The contractor is responsible for implementing the waste management plan, which includes estimating the types and quantities of waste materials, identifying the diversion strategies, selecting the waste haulers and recyclers, tracking and documenting the waste diversion performance, and training the subcontractors and workers. The contractor can provide valuable input on how to reduce, reuse, and recycle the construction and demolition waste, as well as identify potential challenges and opportunities for achieving the prerequisite requirements.
References:
* Reference Guide for Building Design and Construction v4 – Pages 263-2641
* LEED Certification and Sustainable Construction Waste Management1

Q147. Which of the following would be most useful to a school project that is attempting to pursue Water Efficiency Credit, Indoor Water Use Reduction?

A standard garbage disposal

Electronic submeter at the domestic water supply pipe to the building

An open-loop HVAC system that discharges potable cooling water to a nearby lake

Commercial dishwasher that is ENERGY STAR labeled or performance equivalent

Explanation
The Water Efficiency Credit, Indoor Water Use Reduction aims to reduce indoor water consumption by installing water-efficient fixtures and fittings, such as faucets, showerheads, toilets, and urinals1. A commercial dishwasher that is ENERGY STAR labeled or performance equivalent would help reduce the water use for dishwashing, which is one of the process water uses included in the credit calculation2. A standard garbage disposal would not reduce water use, but rather increase it. An electronic submeter at the domestic water supply pipe to the building would help measure and monitor water use, but not directly reduce it. An open-loop HVAC system that discharges potable cooling water to a nearby lake would waste a lot of water and potentially harm the environment.
References:
* Indoor Water Use Reduction
* “Maximizing Water Efficiency in Commercial Buildings: Understanding LEED BD+C Water Efficiency Credits”

Q148. During the early stages of a LEED for Schools project, the team was able to reduce the number of lighting fixtures in classrooms by 25% because the project team selected paint color whose light reflectance value was
75% instead of the initially proposed 64% value. This strategy is an example of applying which of the following credits to the project?

Innovation Credit, Innovation

Integrative Process Credit

Indoor Environmental Quality Credit, Interior Lighting, Option 1. Lighting Control

Materials and Resources Credit, Interiors Life-Cycle Impact Reduction

Explanation
The Integrative Process Credit is a credit in LEED Building Design and Construction that supports high-performance, cost-effective project outcomes through an early analysis of the interrelationships among systems1. The credit requires project teams to perform analyses for both energy- and water-related systems before completing the schematic design, and to use the findings to inform the owner’s project requirements, basis of design, and design and construction documents1. The example given in the question is an illustration of how selecting a paint color with a higher light reflectance value can reduce the energy use and cost of lighting fixtures, which is an energy-related system. This strategy shows how the project team applied an integrative process to evaluate the impacts of different design options on the building performance and environmental benefits. Therefore, the correct answer is B. Integrative Process Credit.
References:
Integrative Process

Q149. An owner has requested that the project team redesign a large office building. As part of the redesign, the owner would like to move the main entrance to the opposite side of the building. Achievement of which credit may be affected by the move?

Location and Transportation Credit, High-Priority Site

Location and Transportation Credit, Sensitive Land Protection

Location and Transportation Credit, Surrounding Density and Diverse Uses

Location and Transportation Credit, LEED for Neighborhood Development Location

Explanation
Achievement of the Location and Transportation Credit, Surrounding Density and Diverse Uses may be affected by the move of the main entrance to the opposite side of the building. This is because the credit requires that the project be located within a minimum density area and within walking distance of diverse uses1. The walking distance is measured from a main functional entry of the project building to the diverse use entry1. If the main functional entry is moved, the distance to the diverse uses may change and affect the credit achievement. The other credits are not affected by the move of the main entrance, as they are based on the location of the project site, not the building entry. The Location and Transportation Credit, High-Priority Site rewards projects that are located on sites that are previously developed, infill, or adjacent to existing development2. The Location and Transportation Credit, Sensitive Land Protection rewards projects that are located on sites that do not contain sensitive land features such as prime farmland, wetlands, or habitats3. The Location and Transportation Credit, LEED for Neighborhood Development Location rewards projects that are located within the boundary of a LEED for Neighborhood Development certified plan4.
References:
*Surrounding density and diverse uses, p. 1
*High-priority site, p. 1
*Sensitive land protection, p. 1
*LEED for neighborhood development location, p. 1

Loading …

Get 100% Real Free USGBC LEED LEED-AP-BD-C Sample Questions: https://www.latestcram.com/LEED-AP-BD-C-exam-cram-questions.html

Related Certifications

C_THR82_2305 (1)
C-TS411-2022 (1)
C_THR97_2211 (1)
C-TADM-22 (1)
C_C4HCX_24 (1)
C_TS413_2020 (1)
C-TS422-2020 (1)
C-S43-2022 (1)
C_FIORDEV_21 (1)
C_THR84_2211 (1)

Free Cram & Latest Exams Dumps

Study HIGH Quality LEED-AP-BD-C Free Study Guides and Exams Tutorials [Q134-Q149]

leave a comment Cancel reply

Related Certifications

Recent Posts

Archives

Categories